Existing Boiler Job Ready Package

75’ From Furnace to Home

Plus 50’ Inside Home

Factory Pre-Plumbing Saves You 4 to 6 Hours

• 1 - 6' x 6' Geotextile Ground Cover
• 4 -12x12x1 Foot Pads
• 1 - Standard Back of Furnace w/0011 pump
  • 1 - TACO 0011 Circulator Pump (for up to 75')
  • 1 - 1" Threaded flanges for circulator (set)
  • 2 - 1" Brass Full Port Ball Valves (threaded)
  • 2 - 1" PEX x 1" Male Adapter fittings
  • 2 - 1" PEX Crimp Rings
  • 1 - 1" Brass x 2" Nipple
  • 2 - 1" Brass 45 Ell
  • 1 - 1" Brass Cap
  • 1 - 1" Brass Plug
  • 1 - 1" Brass 90 Ell
  • 4 - 1" Brass x Close Nipple
  • 1 - 3/4" Bronze Boiler Drain
  • 1 - 3/4" x 3/4" Hose Swivel Adapter
  • 2 - Rubber Washer

Between The Home and The Furnace (Underground)

(Enough material to set the furnace 75' from the home. Additional distance is available.)

• 150' - 1" High temperature flexible PEX pipe (cross-linked polyethylene)
• 10 - 8' MAXX-R polyethylene closed-cell foam insulation pieces (80' distance)
• 9 - MAXX-R Joint Connector Boots
• 2 - MAXX-R Protective End Cap Boot
• 18 - Joint Boot Ties
• 6' - 1 1/8" ID x 1" wall Transition Insulation

Inside The Home

• 50' - 1" High temperature flexible PEX pipe (cross-linked polyethylene)
• 54' - 1-1/8" ID x 1/2" wall closed-cell insulation (to cover the pipes inside/under the home)
• 1 - Roll of 2" wide closed cell insulation tape (to join the insulation)
• 10 - 1" PEX x 1" PEX Brass elbows
• 2 - 1" PEX couplings
• 24 - 1" PEX Crimp Rings

1 - Inline Air Removal Drain Kit

This little package allows you to use your home's water supply to purge the hydronic system of air.

• 1 - 3/4" x 3/4" Hose Swivel Adapter
• 2 - Rubber Washer
• 1 - 3/4" Bronze Boiler Drain
• 1 - 1" x 1" x 3/4" Threaded Brass Tee
• 2 - 1" PEX x 1" Male Adapter fittings
• 2 -1" PEX Crimp Rings
• 1 - Labor to assemble and test

Existing Boiler

(Illustration)

Existing Boiler Work Sheet - PDF 144 KB

Water-To-Water Heat Plate Exchanger

• 1 - 225,000 BTU - 44 Plate Stainless Steel Water-To-Water Heat Exchanger
• 1 - Stainless Steel Flat Plate Heat Exchanger Assembly self install kit including:
  • 2 - 1" WROT FRG x M Adapter
  • 2 - 1" WROT FRG x STR LT 90 EII
  • 2 - 1" WROT CxC Union
  • 2 - 1" WROT FTG x FIP Adapter
  • 2 - 1" Brz 400# Thrd Ball Valve
  • 2 - 1" PEX Barb x 1" MPT Adapter
  • 2 - 1" PEX Crimp Ring
• 1 - Industry Leading Installation Manual

Maintain Your Free Heat Machine

Included FREE with purchase of package

Protect your investment and maintain your warranty by correctly treating the water in your furnace.

Wood Burning Furnace Water Treatment Kit includes:

• 1 gallon of Certified Laboratories “Outdoor Furnace Water Treatment” chemical (treats up to 300 gallons).
• 4 sample bottles for treated furnace water.
• 4 shipping containers, labels and instructions for treated water sample bottles.
• 4 furnace water analyses and reports produced by Certified Laboratories.
• Instructions and procedure sheet.